WEG''s special CWMC contactors series for switching of capacitors is designed according to
AI Customer ServiceSpecification:Specification: Contactors K3-..K are suitable for switching low-inductive and low loss capacitors in capacitor banks (IEC70 and 831, VDE 0560) without and with reactors. Capacitor
AI Customer ServiceCapacitor switching application leads to very high current peak at capacitor energization. UA..RA contactors are designed with damping resistor to handle current peaks without limitation. Product benefits. Widest contactor range on
AI Customer Service3MT7 range of Capacitor duty contactors are designed for switching of power factor correction
AI Customer ServiceDC Switching Contactor 230VAC coil Specifications • Coil Voltage 230.00 • Temperature Range °C -25 to +40°C • IP Rating IP20 • Cable size (mm² (16)-25、32、43、63、85、95
AI Customer ServiceABB offers 3 contactor versions according to the value of the inrush current peak and the power of the capacitor bank. UA..RA Contactors for Capacitor Switching (UA 16..RA to UA 110..RA)
AI Customer ServiceThese special contactors offer several advantages for capacitor switching applications that include series connected reactors: • Safe switching (ON and OFF) of reactor/capacitor steps •
AI Customer ServiceSiemens 3TS capacitor duty contactor works on mechanical delatching operating principle, which ensures reliable switching of capacitors as per AC-6b utilization category at optimum cost.
AI Customer ServiceThe capacitors are precharged during pick-up via early-make contacts and integrated pre-charge resistors before the main contacts close. This combination may be used for switching of
AI Customer ServiceHigh performance AC contactor provides significant damping of inrush current and suppression of voltage transients during switching. AC Contactor Specifications. Model: PEACO-CI19-63.
AI Customer ServiceSpecification: Contactors K3-..K are suitable for switching low-inductive and low loss capacitors
AI Customer ServiceSpecification: Contactors K3-..K are suitable for switching low-inductive and low loss capacitors in capacitor banks (IEC70 and 831, VDE 0560) without and with reactors. Capacitor switching
AI Customer Service2 CWBC - Contactors for Capacitor Switching Main characteristics The special line of CWBC contactors was designed according to IEC 60947-1 and UL 60947-1 standards and provides
AI Customer ServiceA capacitor switching contactor is used for improving the power factor in a single-phase or three-phase system. The contactor can reduce the closing current impact of capacitors. Its current
AI Customer Service3MT7 range of Capacitor duty contactors are designed for switching of power factor correction capacitors. These are reliable and economical solution for capacitor switching. Certification CU
AI Customer ServiceThese switching devices are often combined with the key interlock, protection, and control systems to allow for a fully integrated power capacitor bank. Switching devices include circuit
AI Customer ServiceAs standards, specifications and designs change from time to time, please ask for confirmation of the information given in this publication. Sep.2011 CAPACITOR SWITCHING CONTACTORS
AI Customer ServiceIEC Contactor Specifications Bulletin Numbers 100/104-K, 100/104-C, 100/104S-C, 100/104-E, 100S-E, 100/104-D, 100S-D, 100-G, 100Q-C Topic Page Product Selection—100Q-C
AI Customer ServiceCapacitor switching application leads to very high current peak at capacitor energization. UA..RA contactors are designed with damping resistor to handle current peaks without limitation.
AI Customer ServiceSpecification:Specification: Contactors K3-..K are suitable for switching low-inductive and low
AI Customer ServiceFRAKO capacitor switching contactors are designed for long life, yet they are compact and have low power losses. When switched capacitors do not include series connected reactors, it is
AI Customer Service2 CWBC - Contactors for Capacitor Switching Main characteristics The special line of CWBC
AI Customer ServiceSuppression of voltage transients during switching Protection for both capacitor and contactor Extended capacitor and contactor life . Contactors without pre-charge resistors (K3-..A.. type)
AI Customer ServiceThe capacitors are precharged during pick-up via early-make contacts and integrated pre
AI Customer ServiceThese special contactors offer several advantages for capacitor switching applications that
AI Customer ServiceWEG''s special CWMC contactors series for switching of capacitors is designed according to IEC 60947-1 and UL, and provides the best solution for the switching of power factor
AI Customer ServiceCapacitor switching contactors are fitted with early make contacts and damping resistors, to reduce the value of make current <70 x Ie. Operating Conditions: Capacitor switching contactors are protected against contact welding for a prospective making current of 200 x Ie.
The new range of capacitor duty contactor has been launched to provide a reliable and economical solution for capacitor switching applications. In Low Voltage industrial installations, capacitors are mainly used for reactive power correction (raising the power factor).
It is always recommended to use dedicated capacitor duty switching contactor for switching capacitor bank, which optimizes the switchgear cost & enhances the equipment life. Siemens 3MT7 capacitor duty contactors are specially designed to meet stringent requirements of capacitor switching as deliberated above.
Siemens 3TS capacitor duty contactor works on mechanical delatching operating principle, which ensures reliable switching of capacitors as per AC-6b utilization category at optimum cost. automatic return to the open position of the auxiliary contacts after the main contacts are closed.
We offer a wide product range which caters to fulfill the demand of our esteemed customers with satisfactory performance level and improved reliability. 3MT7 range of Capacitor duty contactors are designed for switching of power factor correction capacitors. These are reliable and economical solution for capacitor switching.
WEG’s special CWMC contactors series for switching of capacitors is designed according to IEC 60947-1 and UL, and provides the best solution for the switching of power factor correction capacitors. When capacitor banks are switched, the voltage associated with a low line impedance may produce high currents on the capacitors.
We are deeply committed to excellence in all our endeavors.
Since we maintain control over our products, our customers can be assured of nothing but the best quality at all times.